14 Jan One of the more common American Society for Testing and Materials (ASTM) tests to evaluate abrasive wear resistance is the ASTM G 3 Jul The graph below presents the results of abrasion resistance tests performed in accordance with the ASTM G65 standard – Procedures A and B. ASTM G65 – 04() Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus. Background: Abrasive wear of industrial.

Author: Gogore Dizilkree
Country: Austria
Language: English (Spanish)
Genre: Automotive
Published (Last): 12 January 2004
Pages: 15
PDF File Size: 1.48 Mb
ePub File Size: 15.75 Mb
ISBN: 772-5-72779-347-9
Downloads: 41779
Price: Free* [*Free Regsitration Required]
Uploader: Faujar

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The test allows comparison of wear-resistant materials by their volume loss in cubic millimeters, with materials of higher wear resistance showing lower volume loss. This standard does not purport to address the safety concerns, if any, associated with its use.

Grinding with a surface grinder can be a controlled form of low stress abrasion. These capabilities allow us to verify mechanical properties and microstructures of materials and coatings, analyze heat treatments, and perform failure analyses and competitive analyses.

Engineered Surfaces to Extend Service Life and Performance

Link to Active This link will always route to the current Active version of the standard. The operating forces must be low enough to prevent crushing the abradant.

Kondex employs three metallurgists with different industry backgrounds and experience levels. This testing also saves customers considerable time and money in field testing, allowing them to focus their efforts on the most promising products. It is particularly useful in ranking materials of medium to extreme abrasion resistance. This machine enables us to compare materials, heat treatments, and coatings for wear resistance, a major concern for our customers.

Its value lies in predicting the ranking of materials in a similar relative order of merit as would occur in an abrasive environment. Low-Stress Abrasion Abrasive wear occurs when hard particles are compressed with normal pressure against the surface of a metal, causing material removal.

Abrasive Wear Test ASTM G65 – Extreme Coatings

ASTM G65 wear tester. Test Conditions Tested for revolutions at a load of 30 lb. Get Access Get Access. These metallurgists provide quality control, design, and analysis services, as well as research on new materials, heat treatments, coatings, aztm manufacturing processes that keep Kondex and our customers up-to-date on industry trends and new technologies.

One lot had a significantly different amount of void content among the individual particles but demonstrated similar results to the other lots in wear rate, chemical composition, size distribution and g6 shape. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. It also provides hard data to an otherwise subjective performance indicator that can be used for marketing and sales. Note 1In order to attain uniformity among laboratories, it is the intent of this test method to require that volume loss due to abrasion be reported only in the metric system as cubic millimetres.

Sample preparation equipment in Kondex metallurgical lab.

Abrasive wear occurs when hard particles are compressed with normal pressure against the surface of a metal, causing material removal. Volume loss data obtained from test materials whose lives are unknown in a specific abrasive environment may, however, be compared with test data obtained from a material whose life is known in the same environment.

It is particularly useful in ranking materials of medium to extreme abrasion resistance. In this practice these conditions are standardized to develop a uniform condition of wear which has been referred to as scratching abrasion 1 and 3.

The low stress qualifier means that the abradant is imposed on the surface with relatively low normal forces. It may be used for highly abrasive resistant materials but is particularly useful in the ranking of medium- and low-abrasive-resistant materials. Hardness testing equipment, microscopes and digital imaging at Kondex.

Click here to increase the life of your mud rotors.

Since the practice does not attempt to duplicate all of the process conditions abrasive size, shape, pressure, impact, or corrosive elementsit should not be used to predict h65 exact resistance of a given material in a specific environment.

It is also used in ranking materials of a specific generic asm or materials which would be very close in asrm volume loss rates as developed by Procedure A. Procedure B should be used when the volume-loss values developed by Procedure A exceeds mm 3. The value of the practice lies in predicting the relative ranking of various materials of construction in an abrasive environment.

The comparison will provide a general indication of the astn of the unknown materials if abrasion is the predominant factor causing deterioration of the materials. It is the intent of this test method to produce data that will reproducibly rank materials in their resistance to scratching abrasion under a specified set of conditions. Abrasive Wear Test ASTM G65 Surfaces subjected to low stress abrasion show that material has been removed by hard, sharp particles or other hard, sharp surfaces plowing material out in the furrows.

The five lots of the abrasive, purchased from U.

At Your Service

By continuing you agree to the use of cookies. We use cookies to help provide and enhance our service and tailor content and ads. Tested for revolutions at a load of 30 lb.

Link to Active This link will always route to the current Active version of the standard. Recommended articles Citing articles 0. Abstract Standardized testing requires consistency of all testing parameters including consumables.